Home Page | Jenny Cells | Model SAH806-4M | Model SA404-2MQ | Jenny Cell Catalog | Sophie Cells | Joe Cell Notes | Joe Cell Test | FAQ | Payments - Devices | Contact | Disclaimer
ver. 1.0.7; last updated 10/31/2019
This page offers information on an early massive prototype of a type I Jenny Cell which I created in my shop and lab. The device shown here is the Model SAH806-4M. It was developed for research purposes and with the secondary goal of using it to gradually infuse my home and laboratory with aetheric energy. Some notes and photos follow.
A Few Photos of a Large Early Jenny Cell Type I Prototype: Model SAH806-4M
The early Jenny Cell prototypes which I created in my shop and lab were rather massive. The Jenny Cell type I Model SAH806-4M prototype shown in the photos below employed a 6-cylinder set of concentric coaxially-arranged stainless steel tubes measuring 8 inches high, with the outermost steel tube measuring four inches in diameter. The cell was sealed top and bottom with polyester resin after filling with the "aetheric flux dielectric" and then capped with a 1/4" thick PVC disk top and bottom for further sealing and protection of contents. The entire 8.5 inch high by 4 inch diameter assembly was then mounted inside a 6.25" diameter PVC pipe measuring 13.5" inches in height.
The gray plastic box mounted on the front of the completed Jenny Cell outer PVC shell contains some exotic components crafted in my lab which condition (by injecting aetheric energy in each lead) and decouple the positive and negative legs of the DC bias voltage from the DC source (in this case, a sealed lead-acid gel-type 12 VDC battery.) The purpose of the decoupling portion of the circuitry in the box is to prevent the DC source or associated wiring from acting as an aetheric energy shunt across the Jenny Cell, whereas an unprotected/non-decoupled DC source would unintentionally drain the Jenny Cell of some of its aetheric energy charge.
The black rectangular object shown alongside the Jenny Cell in some of the photos is a 12 volt DC gel battery which provided the DC bias voltage to accelerate cell charging with aetheric energy. Due to the extremely low current draw of the device, even a tiny 9 volt battery would have performed just as well (and would have lasted for years), but, for the early prototype versions of the device, I chose to employ the larger 12 volt gel cell because it had been pre-conditioned with aetheric energy, and thus it offered additional benefits (i.e., aetheric energy-boosted charging) while serving as a DC bias voltage source in charging the Jenny Cell. Later versions of the large Jenny Cell type I devices employ a small 9 volt DC battery mounted inside the top cap and connected via a short cable and connectors to the DC input of the conditioning/decoupling assembly mounted on the front of the Jenny Cell external housing.
A copy of the front label on the prototype device.
A copy of the specification label on the prototype device.
A front view of the completed device, showing the outer PVC shell which measures almost 14 inches tall and 6.25 inches in diameter. The black rectangular object to the left of the Jenny Cell is a 12 volt DC gel battery which provided DC bias voltage to accelerate cell charging. Due to the extremely low current draw of the Jenny Cell, even a tiny 9 volt battery would have performed just as well and would have lasted for years, but, for early versions of the device, I chose to employ the larger 12 volt gel cell because it had been pre-conditioned with aetheric energy, and thus it offered the additional benefit of an aetheric energy boost while helping to charge the Jenny Cell. The transparent plastic measuring cup shown in the foreground offers some perspective on relative size of components.
Another view of the front of the Jenny Cell prototype. Again, as noted earlier, the black rectangular object to the left is a 12 VDC battery.
Another view of the front of the device, with a very curious kitten in the background.
A side view of the device, showing the two sturdy handles for carrying, and also showing four test jacks on top of the device. You can see the front legs and face of a curious kitten in the upper background.
A close-up of the side of the device, showing the handles and the DC bias supply conditioning/decoupling box mounted on front of the device.
A side view of the Jenn Cell SQAE charger.
A top view of the Jenny Cell charger. The four jacks atop the cap are test jacks.
A close-up side view of the Jenny Celll itself, measuring 8 inches high and 4 inches in diameter. Cell contains 6 stainless steel tubes. The "dry" cell is entirely sealed top and bottom with polyester resin and a plastic cap on each end.
A close-up of the top of the Jenny Cell.
The Jenny Cell emplaced inside the outer tube, as the potting process is underway. The entire cell was ultimately potted and sealed inside the outer PVC shell using polyester resin.
As time passed, I eventually modified the original Jenny Cell model shown in the photos above to eliminate the bulky external 12 VDC battery as a DC bias supply, and I mounted a holder for a common 9 volt alkaline battery inside the cap of the device, wired to a small DC output jack mounted also on the cap. I then routed a short length of cable, fitted with a plug to mate with the jack providing 9 VDC power, to the input of the bias supply conditioning/decoupling box mounted on the front of the Jenny Cell external housing. Since the Jenny Cell draws well less than 2 ua (microamperes, equivalent to 0.000002 amperes), which is likely less than the normal internal leakage current found within the battery, the expected operational lifetime for the 9 volt alkaline battery will be at least six years. And, since there exists some good experiential and anecdotal evidence that common alkaline batteries exhibit a longer-than-normal lifetime when exposed to the type of aetheric energy present in, and radiated by, the Jenny Cell, the actual battery lifetime may actually be far longer than that.
I have appended a few photos below showing the prototype Jenny Cell Model SAH806-4M after switching to the internal 9 VDC bias supply battery.
A side view of the Jenny Cell device after modifiction to use an internally-mounted 9 VDC alkaline battery.
Another side view, showing the short cable and the plug/jack combination on the top of the cell housing.
And finally, a view of the top of the Jenny Cell housing, showing another view of the DC power jack and plug. The 9 volt battery holder is mounted on the underside of the cap, adjacent to the DC power jack.
Here is information on email list group which I operate and which cover these fields or related fields.
The Forbidden Science (VP) group hosted at Groups.io encompasses and subsumes topics covered by each of the several relevant legacy list groups that I had operated at private Yahoo Groups, including Exotic Energies, Ormus-like, Ormus PWT, Time-Space Doorways, Elixir Vitae, Jenny Cell, Radiation Hormesis/Radiation Nutrition, and Quantum Quiet (space effect devices) legacy list groups.
Forbidden Science (VP)
The term "Forbidden Science" was first coined in the 1980s by Dr. Jaques Vallee, a PhD computer scientist and strange/fringe science researcher, to describe those fields of scientific investigation that the current scientific "establishment" tends to view as quack science, or as fringe science, and as undesirable topics for "serious" scientists to research; those fields include the topic of UFOs and "space aliens", alchemy, ormus nutritionals, the paranormal, overunity devices, exotic energies (aka prana or chi) beyond the pale of conventional electromagnetics, and numerous other "fringe science" and "strange science" realms.
This list group serves as a continuation of the various legacy Forbidden Science list groups, listed above, that were operated by Vinny Pinto for 15+ years until the October 2019 downscaling of Yahoo Groups. Vinny is a mystic, spiritual teacher/guide, spiritual healer, and a multi-disciplinary consulting and R&D scientist/engineer.
The primary focus of this list group is to discuss topics in the realms of forbidden science, aka strange science, aka fringe science, including UFOs and "space aliens", alchemy, ormus nutritionals, the paranormal, overunity devices, exotic energies (aka prana or chi) beyond the pale of conventional electromagnetics, and numerous other "fringe science" and "strange science" realms.
While the name and description of this list group are publicly listed at Groups.io and on search engines, all posts sent to the list group are private and are viewable by list group members only. This is a moderated list group. Further, all applicants wishing to join the list group must state their reasons for wishing to join along with their name and general location, and all posts sent to the list group must be signed with the poster's first and last name in order to be published. We do not tolerate hate posts, and we do not tolerate trolls, nor troll posts.
How to Join
If you are interested in joining this list group, you may do so by visiting the list group home page and clicking "Join" at:
Or you may send an email to:
Please note that the list group, as is true of all of my email list groups, are restricted-membership list groups, and thus, once you have applied to join, you will then shortly receive an email from the Groups.io mailserver, entitled something along the lines of "Your Pending Membership in….", which will ask you for certain information; you will need to send the requested information (including your first and last name) back to the list group moderators by replying to the message if you wish your application for membership to be approved.
Here is a brief guide to the pages on this site; more pages will be added as time passes:
- Home Page
- Jenny Cells
- Jenny Cell Prototype Model SAH806-4M
- Jenny Cell for Automative Use, Model SA404-2MQ
- Jenny Cell Prototype Products/Catalog
- Sophie Cells
- Joe Cell Notes
- Joe Cell Cylinder Test
- Payment for Devices
- Contact Information
- Disclaimer Notice
Please note: This material is offered solely for educational and informational purposes. Any technologies or devices mentioned on this page are experimental prototypes only, produced for the sole purposes of research and Proof of Principle evaluation by professional or individual researchers or experimenters. The reader understands that the author is not engaged in rendering health or medical advice or services. The site owner and authors provide this information, and the reader accepts it, with the understanding that people act on it at their own risk and with full knowledge that they should consult with licensed primary care medical professionals for any medical assistance they may need. The author(s) of the material presented on this site are neither medical nor nutritional professionals.
The statements on this site about these technologies have not been evaluated by the FDA. The products and/or technologies mentioned on this website are not intended to diagnose, treat, cure or prevent any disease. If you are ill, please contact a licensed healthcare practitioner.